They are the Thermocouples which cover the widest range of use, from chemical processes to incinerators.

The TC Series has been developed to ensure the best performace-service-cost ratio, from the ease of selection and ordering to the product's maximum reliability and endurance.

Based essentially on DIN norms and thanks to the variety of options, the TC Series also fulfils the other international standards （ISO, ANSI, ...）, which are commonly followed in the practice of engineering.

Type J or type K, grounded or ungrounded measurement junction, general purpose or Atex certified transmitter, can simply be selected according to your requirements.

Furthermore, in the case of applications in industrial furnaces or in the field of primaries, the TAF Thermocouples are often the best-fitting solution.

Thermocouple sensor with compression fitting.

The thermometer TEC420 comprises a TEC100 6 mm diameter inset with either a transmitter mounting plate or a ceramic terminal block. The hot junction can be either grounded or isolated from the sheath. The terminal head can be selected from a wide choice of standard items.

E+H工业热电偶Omnigrad T TEC420

TEC420 sheathed thermocouples cover temperature ranges from -40°C to 1100°C depending on the type of thermocouple. They can be used in low pressure applications in direct contact with the medium or protected by a thermowell. They can also be used in all applications where small immersion lengths are needed. Special attention should be paid to the maximum operating temperature of the connection head （80°C if transmitter included）.

Omnigrad M

TC10

• To screw in
• Thermowell acc. DIN 43772/2G+3G
• Replacable insert, MgO
• Type J （Fe-CuNi）
  Range: -40...750°C 
  （-40...1382°F）
• Type K （NiCR-Ni）
  Range: -40...1100°C
  （-40...2012°F）

TC12

• With compression fitting
• Thermowell acc. DIN 43772/2+3
• Replacable insert, MgO
• Type J （Fe-CuNi）
  Range: -40...750°C
  （-40...1382°F）
• Type K （NiCR-Ni）
  Range: -40...1100°C
  （-40...2012°F）

TC13

• With flange
• Thermowell acc. DIN 43772/2F+3F
• Replacable insert, MgO
• Type J （Fe-CuNi）
  Range: -40...750°C
  （-40...1382°F）
• Type K （NiCR-Ni）
  Range: -40...1100°C
  （-40...2012°F）

Omnigrad S

TC15

• Thermowell acc. DIN 43772/4 + 4F
• Interchangeable insert, MgO
• Type J （Fe-CuNi）
  Range: -40...750°C
  （-40...1382°F）
• Type K （NiCr-Ni）
  Range: -40...1100°C
  （-40...2012°F）

TC88

• To screw-in in an existing thermowell
• Degree of protection up to IP 68
• Replaceable insert, MgO
• Type J （Fe-CuNi）
  Range: -40...750 °C
  （-40...1382 °F）
• Type K （NiCr-Ni）
  Range: -40...1100 °C
  （-40...2012 °F）

德国E+H工业热电偶由一对或多对热电极与绝缘物组成的组件，用来防止热电极之间和（或）热电极与保护管之间短路的零件或材料，保护热电极组件免受环境有害影响的管状物，若与所配用的热电偶正确连接，就把热电偶的参比端移至这对导线的输出端。 在温度出现阶跃变化时，E+H工业热电偶的输出变化至相当于该阶跃变化的某个规定百分数所需的时间，通常以τ表示。